Performance evidence

GNSS Anti-Jam & Anti-Spoof Test Planning

A credible GNSS resilience test links the quoted configuration to a defined signal or threat scenario, an explicit system boundary, recorded receiver or host outputs and measurable pass/fail criteria.

ACCEPTANCE PRINCIPLE

A credible GNSS anti-jam or anti-spoof acceptance test links the quoted hardware and software configuration to a defined RF scenario, explicit system boundary, synchronized measurements, pass/fail limits and recovery criteria. A demonstration video alone does not establish performance.

Supplied demonstration

NOVA-S65 platform video.

This demonstration is provided as integration evidence. It is not a substitute for a configuration-specific acceptance report with stated RF conditions and pass/fail criteria.

Choose the test method for the evidence required

Test methodUseful evidenceImportant limitation
Bench and interface checkPower, communications, RF path, receiver outputs and configuration controlDoes not reproduce spatial or platform effects
Simulator or conducted RF testRepeatable signal, interference and receiver-response comparisonSystem boundary and channel architecture must be stated
Record and replayRepeatable regression against a captured RF environmentEvidence is limited to the recorded scenario and playback setup
Radiated or chamber evaluationAntenna, spatial processing and integrated RF-chain behaviorFacility geometry, calibration and installation representation matter
Representative-platform checkMounting, cabling, self-interference and host-system responseMust remain authorized and cannot replace controlled repeatability

The European Space Agency Navigation Laboratory lists GNSS signal simulators, signal recording and playback, anomaly simulation and an anti-spoofing test bed among its receiver-evaluation capabilities. See the ESA Navigation Laboratory overview. A supplier report should state which method was used and what part of the complete system it evaluates.

Build a buyer-ready acceptance record

Record stageWhat to captureWhy buyers need it
Configuration controlHardware identifier, software version, interfaces, setup drawing and calibration stateLinks the result to the quoted system
BaselineDesired GNSS condition, tracked signals, receiver status and host output before disruptionCreates a reference for comparison
Applied scenarioWaveform or threat definition, bandwidth, power, geometry, timing and protected bandsMakes the exposure repeatable and comparable
System responseSynchronized RF, receiver, alert and host-system outputsShows what happened across the stated system boundary
RecoveryClear condition, reacquisition, return to trusted output and repeated-run resultVerifies behavior after the disruption ends

Acceptance should use one agreed matrix for the supplier and buyer. Any published suppression, detection or recovery result should be read together with its test conditions and measurement point.

Information to capture

Signal environment

Protected constellation, frequency and desired GNSS signal condition.

Interference definition

Waveform, bandwidth, input power, direction count and geometry.

System boundary

Antenna array, processing electronics, receiver and host-platform interfaces.

Measured output

RF, C/N₀, position, timing, availability or another agreed observable.

Platform constraints

Mounting, cabling, radome, nearby emitters, voltage and environment.

Decision criteria

Pass/fail thresholds, repetitions, records and responsible parties.

Suggested validation stages

  1. Document reviewConfirm the configuration, interfaces and acceptance matrix.
  2. Bench verificationCheck power, communication and protected-signal behavior.
  3. Controlled RF evaluationApply the agreed scenario in an authorized test environment.
  4. Representative-platform checkVerify installation effects and host-system behavior.

Questions procurement teams ask

What should a GNSS anti-jam test report include?

Record the quoted hardware and software configuration, protected constellations and bands, desired-signal condition, interference waveform, bandwidth, power, direction and geometry, system boundary, measurement point, receiver or host outputs, pass/fail limits, repetitions and recovery behavior.

Is a headline suppression value enough for acceptance?

No. A suppression figure is only comparable when the waveform, input level, geometry, protected bands, system boundary and measurement method are stated. Platform installation and receiver behavior should be checked separately under agreed conditions.

Which outputs should be logged during a GNSS resilience test?

Use synchronized timestamps to record the applied RF condition and relevant outputs such as C/N₀, tracked satellites, receiver solution status, position or timing error, alerts, host-system mode, loss or rejection behavior, reacquisition and recovery. The required list depends on the stated system boundary.

Is a demonstration video sufficient acceptance evidence?

No. A video can show installation or visible host behavior, but it does not establish the RF waveform, input level, geometry, protected bands, measurement point, configuration or pass/fail result unless those items are documented separately.

How should GNSS anti-spoofing behavior be evaluated?

Use an authorized simulator, record-and-replay setup or other controlled facility with a defined threat model. Record detection, alert latency, mitigation or rejection, position or timing behavior, host-system response, false alarms and recovery to trusted navigation.

Authorized testing only

RF interference and spoofing tests must be conducted in properly authorized, controlled or shielded facilities and in accordance with applicable spectrum rules.

Next step

Build a configuration-specific acceptance brief

Share platform, protected bands, interfaces and project timing. Zhiyunlai will confirm a suitable starting configuration and the information needed for validation.

Request quote & model reviewWhatsApp
WhatsAppTalk to an engineer